Written by andi.eti
Hits (1530) || Comments (0)
Created Monday, 11 August 2008
Last updated Monday, 11 August 2008
| Title | Ethernet minimodule with ARM7TDMI <b>AT91SAM7x</b> from Atmel | |
| Description |
Features MMnetSAM7x minimodule - Complete, ready to use microprocessor system - Fast ARM7TDMI microcontroller AT91SAM7x - Up to 512kB Flash memory and up to 128kB RAM - Onboard Ethernet PHY and RJ45 connector with embedded magnetics - Serial DataFlash memory 64Mb (8MB) - Reset circuit - Built-in 18.432MHz crystal resonator - Onboard USB pull-up circuit - Built-in voltage regulator 3.3V 400mA - Module supply voltage: 3.3V or 3.8 - 16V - 2 LED diodes indicating: power, LAN Full Duplex activity - 2 x 40 terminals with 0.1" (2.54mm) pitch fitting every prototype board - Small dimensions: 56mm x 48mm - Available evaluation board and sample applications
AT91SAM7x microcontroller - ARM7TDMI ARM Thumb Processor - High-performance 32-bit RISC Architecture - Leader in MIPS/Watt - Fully Static Operation: Up to 55 MHz at 1.65V and 85°C Worst Case Conditions Internal High-speed Flash - 128 to 512kB In System Programmable Flash memory - Internal High-speed SRAM, Single-cycle Access at Maximum Speed - 32 kB to 128kB of SRAM - Memory Controller (MC) - Reset Controller (RSTC) - Clock Generator (CKGR) - Low-power RC Oscillator, 3 to 20 MHz On-chip Oscillator and one PLL - Power Management Controller (PMC) - Advanced Interrupt Controller (AIC) - Debug Unit (DBGU) - Periodic Interval Timer (PIT) - Windowed Watchdog (WDT) - Real-time Timer (RTT) - Two Parallel Input/Output Controllers (PIO) - Thirteen Peripheral DMA Controller (PDC) Channels - One USB 2.0 Full Speed (12 Mbits per second) Device Port - One Ethernet MAC 10/100 base-T - One Part 2.0A and Part 2.0B Compliant CAN Controller - One Synchronous Serial Controller (SSC) - Two Universal Synchronous/Asynchronous Receiver Transmitters (USART) - Two Master/Slave Serial Peripheral Interfaces (SPI) - One Three-channel 16-bit Timer/Counter (TC) - One Four-channel 16-bit Power Width Modulation Controller (PWMC) - One Two-wire Interface (TWI) - One 8-channel 10-bit Analog-to-Digital Converter, Four Channels Multiplexed with Digital I/Os - SAM-BA Boot Assistance - IEEE 1149.1 JTAG Boundary Scan on All Digital Pins - 5V-tolerant I/Os, Including Four High-current Drive I/O lines, Up to 16 mA Each - Power Supplies - Embedded 1.8V Regulator, Drawing up to 100 mA for the Core and Ext Comp - Available in 100-lead LQFP Green and 100-ball TFBGA Green Packages
Ethernet PHY DM9161A - Fully comply with IEEE 802.3 / IEEE 802.3u 10Base-T/100Base-TX - Support MDI/MDI-X auto crossover function - IEEE 802.3u Auto-Negotiation - Selectable MII or RMII - Selectable full-duplex or half-duplex operation - LED status outputs indicate Link/Activity - Single Supply of 3.3V - Low power consumption - Low power modes - Campatybile with 3.3V and 5.0V tolerant I/Os www.propox.com | |
| Add links |
|
Comments
There are no comments for this item
Be the first to leave a comment
Login to leave a comment


