u-boot with usb-ethernet adapter

kamejoko80 · **Joined:** Sat Jun 13, 2009 5:50 pm **Posts:** 44

Hello,

The USB-Ethernet adapter's drivers are now avaliable in the latest u-boot version. http://git.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary

Now I'd like to try the ASIX AX88172 adapter with the AT91SAM9260 based board with no success. Here is my log:

Code:

U-Boot> usb reset
(Re)start USB...
USB:   scanning bus for devices... New Device 0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x40
set address 1
usb_control_msg: request: 0x5, requesttype: 0x0, value 0x1 index 0x0 length 0x0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x12
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0x9
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0x19
get_conf_no 0 Result 25, wLength 25
if 0, ep 0
##EP epmaxpacketin[1] = 2
set configuration 1
usb_control_msg: request: 0x9, requesttype: 0x0, value 0x1 index 0x0 length 0x0
new device strings: Mfr=0, Product=1, SerialNumber=0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x300 index 0x0 length 0xFF
USB device number 1 default language ID 0x409
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x301 index 0x409 length 0xFF
Manufacturer
Product      OHCI Root Hub
SerialNumber
USB hub found
usb_control_msg: request: 0x6, requesttype: 0xA0, value 0x2900 index 0x0 length 0x4
usb_control_msg: request: 0x6, requesttype: 0xA0, value 0x2900 index 0x0 length 0x9
2 ports detected
ganged power switching
standalone hub
no over-current protection
power on to power good time: 4ms
hub controller current requirement: 0mA
port 1 is removable
port 2 is removable
usb_control_msg: request: 0x0, requesttype: 0xA0, value 0x0 index 0x0 length 0x4
get_hub_status returned status 0, change 0
local power source is good
no over-current condition exists
enabling power on all ports
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x8 index 0x1 length 0x0
port 1 returns 0
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x8 index 0x2 length 0x0
port 2 returns 0
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
Port 1 Status 101 Change 1
port 1 connection change
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
portstatus 101, change 1, 12 Mb/s
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x10 index 0x1 length 0x0
hub_port_reset: resetting port 0...
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x4 index 0x1 length 0x0
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
portstatus 103, change 10, 12 Mb/s
STAT_C_CONNECTION = 0 STAT_CONNECTION = 1  USB_PORT_STAT_ENABLE 1
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x14 index 0x1 length 0x0
New Device 1
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x40
hub_port_reset: resetting port 0...
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x4 index 0x1 length 0x0
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
portstatus 103, change 10, 12 Mb/s
STAT_C_CONNECTION = 0 STAT_CONNECTION = 1  USB_PORT_STAT_ENABLE 1
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x14 index 0x1 length 0x0
set address 2
usb_control_msg: request: 0x5, requesttype: 0x0, value 0x2 index 0x0 length 0x0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x12
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0x9
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0x27
get_conf_no 0 Result 39, wLength 39
if 0, ep 0
if 0, ep 1
if 0, ep 2
##EP epmaxpacketin[1] = 16
##EP epmaxpacketout[2] = 64
##EP epmaxpacketin[3] = 64
set configuration 1
usb_control_msg: request: 0x9, requesttype: 0x0, value 0x1 index 0x0 length 0x0
new device strings: Mfr=1, Product=2, SerialNumber=3
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x300 index 0x0 length 0xFF
USB device number 2 default language ID 0x409
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x301 index 0x409 length 0xFF
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x302 index 0x409 length 0xFF
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x303 index 0x409 length 0xFF
Manufacturer ASIX Elec. Corp.
Product      AX172
SerialNumber 01
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x2 length 0x4
Port 2 Status 100 Change 0
2 USB Device(s) found
scan end
       scanning bus for storage devices... 0 Storage Device(s) found
       scanning bus for ethernet devices... hdelete: DELETE key "ethact"
hdelete: DELETING key "ethact"
i=0
i=1


USB Ethernet device detected: 0xb95:0x1720
Endpoints In 3 Out 2 Int 1
i=2
1 Ethernet Device(s) found
U-Boot> ping 192.168.1.3

** asix_halt()
Trying asx0
** asix_init()
asix_write_gpio() - value = 0x00b0
asix_write_cmd() cmd=0x1f value=0x00b0 index=0x0000 size=0
usb_control_msg: request: 0x1F, requesttype: 0x40, value 0xB0 index 0x0 length 0x0
asix_read_cmd() cmd=0x19 value=0x0000 index=0x0000 size=2
usb_control_msg: request: 0x19, requesttype: 0xC0, value 0x0 index 0x0 length 0x2
asix_get_phy_addr()
asix_get_phy_addr() returning 0xe003
asix_write_cmd() cmd=0x22 value=0x0000 index=0x0000 size=0
usb_control_msg: request: 0x22, requesttype: 0x40, value 0x0 index 0x0 length 0x0
ERROR: CTL:TIMEOUT
Select PHY #1 failed
FAIL
** asix_halt()
ping failed; host 192.168.1.3 is not alive

Have you ever tried with ? Anny suggestion for this pls show me how to correct the bug.

Thanks and Best Regards.

u-boot with usb-ethernet adapter

Who is online