Home 
Forum
Forum
| Welcome to AT91SAM Community Forum http://www.at91.com/samphpbb/ |
|
| AT91SAM7S Boot Assistant (SAM-BA) http://www.at91.com/samphpbb/viewtopic.php?f=15&t=674 |
Page 5 of 7 |
| Author: | ChipBurns [ Sun Jul 17, 2005 11:24 pm ] |
| Post subject: | |
I have a 7S-EK board (S64) marked Rev.A3. How do I tell if my uP/dev bd. supports SAM-BA? |
|
| Author: | Fredo_Boyer [ Wed Jul 20, 2005 8:35 am ] |
| Post subject: | |
Check thgat you have a chip version of AT91SAM7S64 > revE: 58814E or 58814G or higher Bye |
|
| Author: | Satanic [ Thu Jul 21, 2005 1:16 pm ] |
| Post subject: | |
pfilippi wrote: Hi,
JPS, the commands available through SAM-BA will be released at the time of the full release. The Download via the Serial debug port (simple TX/RX UART) will use the Xmodem protocol. Actually it would be fine to have it for Linux. The Rev E of the AT91SAM7S64 parts, have the SAM-BA on chip. SAM-BA commands will be someting like read/write a byte, read/write half word, read/write a word, send/receive a file, go, display version Quote: Can full SAM-BA functionality be programmed in to older "engineering sample" versions of the chips over JTAG Yes it can, but will be one-time usable for "old engineering parts". Only Rev G are sampled from now. The best would be to contact your local ATMEL FAE/ ATMEL Distributor to have samples of Rev G. Regards, Can you tell me where can i find that (the protocol/commands)? |
|
| Author: | Fredo_Boyer [ Thu Jul 21, 2005 1:58 pm ] |
| Post subject: | |
Hi Satanic, The commands available through SAM-BA GUI are located in the Help Menu-> SAM-BA User Guide Concerning the protocol and the boot program running on the target, it is available on your product datasheet in the section SAM-BA Boot Assistant : go to www.at91.com to have the last datasheet version ! Bye |
|
| Author: | ChipBurns [ Tue Jul 26, 2005 5:20 am ] |
| Post subject: | |
Where can I go to get SAM-BA v1.5? I've looked all over the web site and not been able to find it anywhere. |
|
| Author: | Fredo_Boyer [ Thu Jul 28, 2005 11:31 am ] |
| Post subject: | |
The latest SAM-BA release is available on the www.atmel.com, see the annoucement made on this list byt the AT91 Team ! http://www.atmel.com/dyn/products/tools ... ol_id=3894 Regards |
|
| Author: | zk543g [ Fri Jul 29, 2005 7:42 am ] |
| Post subject: | enjoy! |
The new SAM-BA release (v1.5) is good !! enjoy! |
|
| Author: | kravitz [ Fri Aug 26, 2005 4:20 pm ] |
| Post subject: | cmd line params |
Hello! How to start script from command line? Thanks |
|
| Author: | Fredo_Boyer [ Fri Aug 26, 2005 4:45 pm ] |
| Post subject: | |
Hi Kravitz, You can find the different commands available through the command line (which is a Tcl interpreter meaning you can use tcl commands + SAM-BA commands) in the SAM-BA User Guide. If you want to save a file with the different commands, the only solution is to use the graphical interface:  A simple way to retrieve commands is to click on Script File Menu -> Start Recording. This allows you to record all the commands you have executed until you click on Stop Recording. Then Edit Script File to retrieve and to use them on the command line...
I hope this will of help to you! |
|
| Author: | kravitz [ Mon Aug 29, 2005 10:54 am ] |
| Post subject: | |
Hi Croquette, Thanks for your attention and sorry because my question was not fully clear. On this site we can read next sentence about SAM-BA: "May be used via a Graphical User Interface or started from a DOS window" My question was: Can I run script by passing script file name as command line parameter of SAM-BA.exe? If now I can't, this way of running script (for examlpe: SAM-BA.exe /r script.tcl) would be very useful in new versions of SAM-BA 
Thanks |
|
| Author: | Fredo_Boyer [ Mon Aug 29, 2005 11:04 am ] |
| Post subject: | |
Hi Kravitz, Good request ! But this is not possible with the current release... If it can represent a great improvement for SAM-BA, we will try to add this functionnality in next releases... Bye |
|
| Author: | Satanic [ Wed Oct 19, 2005 9:45 am ] |
| Post subject: | |
croquette wrote: Hi Kravitz,
Good request ! But this is not possible with the current release... If it can represent a great improvement for SAM-BA, we will try to add this functionnality in next releases... Bye Yes it is since it will allow us to call it from our programs. Btw, what i wanted in my previous post few lines above was the communication protocol used for samba. Is it available?. (then i dont need your program, i can implement it in my software directly). |
|
| Author: | Fredo_Boyer [ Wed Oct 19, 2005 9:48 am ] |
| Post subject: | |
Hi, We are actually working on such a batch program based on SAM-BA which will present the same functionnalities as the GUI but in DOS Command mode... Bye |
|
| Author: | Satanic [ Wed Oct 19, 2005 1:11 pm ] |
| Post subject: | |
CroQueTTe wrote: Hi,
We are actually working on such a batch program based on SAM-BA which will present the same functionnalities as the GUI but in DOS Command mode... Bye A great, thanks a lot .
|
|
| Author: | Fredo_Boyer [ Wed Oct 19, 2005 2:16 pm ] |
| Post subject: | |
You're welcome 
By the way, if you want to understand the protocol SAM-BA Boot uses for uart & usb communication, visit the SAM-BA section on the atmel.com site http://www.atmel.com/dyn/products/tools ... ol_id=3894 Bye ! |
|
| Page 5 of 7 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|
