Hi people,
I'm using the Arm in subject.
I would like to use DAC with DMA(PDC) but I don't found examples about it.
Could you write a little example or explain how to make it please?

Thanks in advance

Mario

I did it for the U series. see if it fits. the ADC is actived by the TC. sorry, but I dont have time to clean the code, so just I pasted it all.


//-----------------------------------------------------------------------------
//-----------------------------------------------------------------------------
void Config_AD12B(void)
{
AT91C_BASE_PIOA->PIO_PDR = AT91C_PIO_PA22 + AT91C_PIO_PA30;
AT91C_BASE_PIOB->PIO_PDR = AT91C_PIO_PB3 + AT91C_PIO_PB4;
AT91C_BASE_PIOC->PIO_PDR = AT91C_PIO_PC15 + AT91C_PIO_PC16 +
AT91C_PIO_PC17 + AT91C_PIO_PC18;

AT91C_BASE_PMC->PMC_PCER = 1 << AT91C_ID_ADC12B;

AT91C_BASE_ADC12B->ADC12B_CR = AT91C_ADC_SWRST;

AT91C_BASE_ADC12B->ADC12B_MR = AT91C_ADC12B_MR_TRGEN_EN +
AT91C_ADC12B_MR_TRGSEL_TIOA_2 +
AT91C_ADC12B_MR_LOWRES_12_BIT +
AT91C_ADC12B_MR_SLEEP_NORMAL +
(0 << + //AT91C_ADC12B_MR_PRESCAL //1
(10 << 16) + //AT91C_ADC12B_MR_STARTUP
(4 << 24); //AT91C_ADC12B_MR_SHTIM //10

AT91C_BASE_ADC12B->ADC12B_CHER = AT91C_ADC12B_CHER_CH0_ENABLE +
AT91C_ADC12B_CHER_CH1_ENABLE +
AT91C_ADC12B_CHER_CH2_ENABLE +
AT91C_ADC12B_CHER_CH3_ENABLE +
AT91C_ADC12B_CHER_CH4_ENABLE +
AT91C_ADC12B_CHER_CH5_ENABLE +
AT91C_ADC12B_CHER_CH6_ENABLE +
AT91C_ADC12B_CHER_CH7_ENABLE;

AT91C_BASE_ADC12B->ADC12B_RCR=1; // Prevents a first not wanted interrup from DMA
AT91C_BASE_ADC12B->ADC12B_IER = AT91C_ADC12B_IER_ENDRX_ENABLE;
//AT91C_BASE_ADC12B->ADC12B_IER = AT91C_ADC12B_IER_EOC7_ENABLE;
IRQ_ConfigureIT(AT91C_ID_ADC12B, 0, ADCC0_IrqHandler);
IRQ_EnableIT(AT91C_ID_ADC12B);
}

//-----------------------------------------------------------------------------
//-----------------------------------------------------------------------------
void Configure_TC(void)
{
AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_TC2);

AT91C_BASE_TC2->TC_CMR = AT91C_TC_CLKS_TIMER_DIV1_CLOCK +
AT91C_TC_BURST_NONE +
AT91C_TC_WAVESEL_UP_AUTO +
AT91C_TC_WAVE +
AT91C_TC_ACPA_SET +
AT91C_TC_ACPC_CLEAR;

AT91C_BASE_TC2->TC_RA = 749;
AT91C_BASE_TC2->TC_RC = 750;
//AT91C_BASE_TC2->TC_RA = 360;
//AT91C_BASE_TC2->TC_RC = 375;
//AT91C_BASE_TC2->TC_RA = 0xFFE0;
//AT91C_BASE_TC2->TC_RC = 0xFFE9;

}

//------------------------------------------------------------------------------
//------------------------------------------------------------------------------
void ADCC0_IrqHandler(void)
{
if((AT91C_BASE_ADC12B->ADC12B_SR & AT91C_ADC12B_IER_ENDRX_ENABLE) != AT91C_ADC12B_IER_ENDRX_ENABLE)
return;

if(ADC_BUFFER_CTRL.buff_full==ADC_BUFFER_1_FULL)
{
ADC_BUFFER_CTRL.buff_full=ADC_BUFFER_2_FULL;
AT91C_BASE_ADC12B->ADC12B_RPR=(unsigned int)ADC_BUFFER_CTRL.adc_buffer [ADC_BUFFER_1] ;
}
else if(ADC_BUFFER_CTRL.buff_full==ADC_BUFFER_2_FULL)
{
ADC_BUFFER_CTRL.buff_full=ADC_BUFFER_1_FULL;
AT91C_BASE_ADC12B->ADC12B_RPR=(unsigned int)ADC_BUFFER_CTRL.adc_buffer [ADC_BUFFER_2];
}
/*buff_in[0]=AT91C_BASE_ADC12B->ADC12B_CDR[0];
buff_in[1]=AT91C_BASE_ADC12B->ADC12B_CDR[1];
buff_in[2]=AT91C_BASE_ADC12B->ADC12B_CDR[2];
buff_in[3]=AT91C_BASE_ADC12B->ADC12B_CDR[3];
buff_in[4]=AT91C_BASE_ADC12B->ADC12B_CDR[4];
buff_in[5]=AT91C_BASE_ADC12B->ADC12B_CDR[5];
buff_in[6]=AT91C_BASE_ADC12B->ADC12B_CDR[6];
buff_in[7]=AT91C_BASE_ADC12B->ADC12B_CDR[7];*/


AT91C_BASE_ADC12B->ADC12B_RCR=ADC_SIZE_BUFFER;
ADC_BUFFER_CTRL.adc_buff_state=ADC_BUFFER_FULL;
AT91C_BASE_PIOC->PIO_CODR = AT91C_PIO_PC9;
AT91C_BASE_PIOC->PIO_SODR = AT91C_PIO_PC9;
// AT91C_BASE_PIOA->PIO_CODR = AT91C_PIO_PA0;
// AT91C_BASE_PIOA->PIO_SODR = AT91C_PIO_PA0;
}
//------------------------------------------------------------------------------
//------------------------------------------------------------------------------
void Config_TC2_ADC12B_PDC(void)
{
AT91C_BASE_ADC12B->ADC12B_PTCR=1;
Configure_TC();
Config_AD12B();
Disable_ADC_TC_PDC();
}
//------------------------------------------------------------------------------
//------------------------------------------------------------------------------
void Enable_ADC_TC_PDC (void)
{
ADC_BUFFER_CTRL.adc_buff_state=ADC_BUFFER_EMPTY;
ADC_BUFFER_CTRL.buff_full=ADC_BUFFER_2_FULL;
AT91C_BASE_ADC12B->ADC12B_RPR=(unsigned int)ADC_BUFFER_CTRL.adc_buffer [ADC_BUFFER_1] ;
AT91C_BASE_ADC12B->ADC12B_RCR=ADC_SIZE_BUFFER;
AT91C_BASE_TC2->TC_CCR = AT91C_TC_SWTRG +AT91C_TC_CLKEN;
}

//------------------------------------------------------------------------------
//------------------------------------------------------------------------------
void Disable_ADC_TC_PDC (void)
{
AT91C_BASE_TC2->TC_CCR = AT91C_TC_CLKDIS;
}
//------------------------------------------------------------------------------
//------------------------------------------------------------------------------

Hi,

You can have a look at the new software package available on www.atmel.com.
The USB audio demo (to get the SAM3S-EK behaving as an USB audio card with the internal ADC and DAC) uses the PDC of the DAC.

Hope it helps.

Regards,
bdenis