How can i use SAM-BA 2.16 to flash Atmel Sama5d2 Xlpained?

For SAMA5D2 Xplained, SAMA5D3 Xplained and SAMA5D4 Xplained

Moderator: nferre

xzp114
Posts: 23
Joined: Thu Mar 16, 2017 12:30 pm

How can i use SAM-BA 2.16 to flash Atmel Sama5d2 Xlpained?

Sat Mar 18, 2017 9:09 am

hi
    When i open sam-ba 2.16, i cannot find my board type. I can see Sama5d3 Xlpained and Sama5d4 Xlpained, but it dosenot have Sama5d2 Xlpained. So how can i do to use this application?
nferre
Site Admin
Posts: 156
Joined: Wed Feb 14, 2007 11:17 am

Re: How can i use SAM-BA 2.16 to flash Atmel Sama5d2 Xlpaine

Mon Mar 20, 2017 12:37 pm

For sama5d2 SoC you must use SAM-BA 3.x.
It is the only tool that is available for this product and the only one that will be maintained in the future.
Best regards
xzp114
Posts: 23
Joined: Thu Mar 16, 2017 12:30 pm

Re: How can i use SAM-BA 2.16 to flash Atmel Sama5d2 Xlpaine

Wed Mar 22, 2017 2:18 am

nferre wrote:For sama5d2 SoC you must use SAM-BA 3.x.
It is the only tool that is available for this product and the only one that will be maintained in the future.
Best regards
Thanks! I see SAM-BA 3.x. supports my board sama5d2. But how can i do to flash u-boot.bin ? Anywhere has the course, like step by step? Thank you very much!
nferre
Site Admin
Posts: 156
Joined: Wed Feb 14, 2007 11:17 am

Re: How can i use SAM-BA 2.16 to flash Atmel Sama5d2 Xlpaine

Wed Mar 22, 2017 10:43 am

I guess that you are looking for this:
http://www.at91.com/linux4sam/bin/view/ ... edMainPage
xzp114
Posts: 23
Joined: Thu Mar 16, 2017 12:30 pm

Re: How can i use SAM-BA 2.16 to flash Atmel Sama5d2 Xlpaine

Sat Mar 25, 2017 10:20 am

nferre wrote:I guess that you are looking for this:
http://www.at91.com/linux4sam/bin/view/ ... edMainPage
I have read this. But i cannot find any useful information for my question. I just see as blow:

Using SAM-BA to flash components to board
Launch SAM-BA tools
According to this section make sure that the chip can execute the SAM-BA Monitor.

How can i do to flash my application(not Linux) on my board? And reboot from my application? Thank you very much! 
blue_z
Location: USA
Posts: 1504
Joined: Thu Apr 19, 2007 10:15 pm

Re: How can i use SAM-BA 2.16 to flash Atmel Sama5d2 Xlpaine

Mon Mar 27, 2017 12:44 am

xzp114 wrote:How can i do to flash my application(not Linux) on my board?
Did you look at the supplied (HTML) documentation that comes with the SAM-BA application (i.e. the doc/ directory)?

Since there is only a command-line interface with SAM-BA 3.x (which has no GUI), booting from SDcard and using U-Boot (or even Linux) is about the same amount of typing (and in the long run, probably more useful & transferable knowledge).

Regards

Return to “SAMA5 Xplained”

Who is online

Users browsing this forum: No registered users and 1 guest